News
New protocols, tool updates and coverage announcements from Autotuner, MagicMotorsport and Dimsport (Race), the platforms we resell and use every day. Summarised by our team, with a link to each original announcement.

FeaturedMagicMotorsport · October 30, 2026
Kefico SIM2K-510 — OBD for Hyundai and Kia, a Flex exclusive
Flex version 8.28.0.0 adds OBD support for the Kefico SIM2K-510 control units of Hyundai and Kia, presented by MagicMotorsport as a Flex exclusive. The ECU is unlocked automatically during the first step, whether a real read or a write. In OBD mode the workshop connects the cable, downloads the Virtual Read and edits it; when no Virtual Read is available, OBD on Bench performs a real read. CAN-FD versions are supported too: the real read follows the connection diagram in the manual, and writing requires the new CAN-FD FLX4.4 adapter. Memories: VR, read, write and checksum maps; licences FLS0.1M/S and FLS0.5M/S; about 30 seconds to connect, 5 minutes to read and 10 minutes to write. Vehicles cited: Hyundai Kona (OS, 2017) and Tucson (NX4, 2020), Kia Ceed (CD, 2018), Sportage (NQ5, 2021) and Stonic (YB, 2017), all 1.6 CRDi. The changelog section of the page was still a placeholder when we read it.
Read more →

BitBox · November 11, 2026
Bosch MD1CP007 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MD1CP007 Gen2 control units from 2020 onwards, built on AURIX TC298 processors and fitted to diesel JLR vehicles, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only.

MagicMotorsport · November 9, 2026
Bosch MD1CP007 / MD1CP017 / MG1CS028 — Korhex unlock for Jaguar and Land Rover
With Flex version 8.31.0.0, MagicMotorsport's Korhex can now unlock Bosch MD1CP007, MD1CP017 and MG1CS028 control units fitted to Jaguar and Land Rover vehicles, previously accessible only through Voltage Fault Injection (VFI). No PCB modification is required; once unlocked, reading and programming continue directly in Bench mode. The new protocols require the FLS0.20 or Flex Full FLS0.5 license.

Autotuner · November 9, 2026
Bosch EDC17CV41 — 100% OBD NR (Beta) for Iveco / CNH
AutoTuner releases, in Beta, 100% OBD Normal Read (NR) support for the Bosch EDC17CV41 control unit (Iveco / CNH), expanding coverage to agricultural, forestry and construction machinery and Iveco commercial trucks: Case IH, New Holland, Claas and Steyr tractors and combines, Tigercat and Logset forestry equipment, Doosan excavators and wheel loaders, and Iveco Eurocargo, Stralis and Trakker trucks. Reading and writing go straight through the diagnostic port, with the New Holland OBD cable required.

Autotuner · November 9, 2026
Bosch MED17.1.62 — OBD VR for Audi, KTM and Volkswagen
The Bosch MED17.1.62, built on the Infineon TriCore TC1793, is now officially supported in OBD Virtual Read (VR) mode on the AutoTuner One personal flasher. It covers the Audi 2.5 TFSI five-cylinder, the same engine and ECU package in the KTM X-BOW GTX and X-BOW GT-XR, and the Volkswagen 3.6 V6 FSI (VR6) of the Atlas and Teramont from 2018 onwards.

Autotuner · November 9, 2026
Visteon DCU102 — OBD VR and Boot NR for Citroën, Peugeot and Fiat
The Visteon DCU102, built on the STMicroelectronics ST10F276, is now officially supported via OBD Virtual Read (VR) and Boot Normal Read (NR) on the AutoTuner Tool. It covers the 2002–2006 Citroën Jumper, Peugeot Boxer and Fiat Ducato, powered by the 2.2 HDi / 2.2 JTD diesel engine.

Dimsport · November 6, 2026
Bosch MG1CS003 — Bench unlock for BMW (RACE plugin 2148)
Dimsport's RACE line, exclusively on TheGenius platform, adds plugin 2148 for the Bosch MG1CS003 (SPC5777, BMW petrol), unlocking in Bench mode ECUs that were previously locked. The same release adds plugin 2142 for the Bosch MG1CS163 H80 (TC298TP, VAG/Bentley petrol) and plugin 2150 for the Bosch MD1CS014 (TC299TP, VAG diesel), both in HVR mode.

Autotuner · November 6, 2026
Motorola EMS S7 — 100% OBD NR (Beta) for Scania
AutoTuner releases, in Beta, 100% OBD Normal Read (NR) support for the Motorola EMS S7 control unit powering Scania G, P and S Series trucks (8.9L DC9 XPI and 11.7L DT12 HPI engines, including the S 500). Reading and writing go straight through the truck's diagnostic socket with no ECU removal, using AutoTuner's dedicated 24V OBD cable; a 24V charger such as the GYSFLASH 101.24 CNT is required to keep the vehicle's voltage stable. The protocol also works OBD on the bench, through a dedicated Scania bench cable.

MagicMotorsport · November 5, 2026
Keihin 38770 / 790.41 / 796.41 (M16C) — Bench for Honda, KTM, Husqvarna, GASGAS
Flex version 8.30.0.0 adds support for Keihin K-line control units built on M16C processors — Honda Keihin 38770-xxx-xxx, and KTM Keihin 790.41 and 796.41 — fitted to Honda, KTM, Husqvarna and GASGAS motocross bikes from 2013 to 2025. Honda units, usually located under the seat, are accessed via a Pinout connection; the KTM, Husqvarna and GASGAS units from the BMAG group support both OBD and Bench connections. For the Honda 38770 and the KTM 796.41, Flex details Bench mode precisely: read, write and checksum of the internal Flash, read and write of the external EEPROM, about 10 seconds to connect, 10 minutes to read and 4 minutes to write. The page gives no separate figures for the 790.41.

Autotuner · November 5, 2026
Bosch MG1CA920 / MG1CA007 / MG1CA770 / MG1CA001 — Bench after Mail-in Unlock
AutoTuner adds Bench support for the Bosch MG1CA920, MG1CA007, MG1CA770 and MG1CA001 control units on powersports vehicles — Can-Am, Sea-Doo, Polaris, Indian, KTM, Husqvarna, Ducati and Kawasaki. The ECU must first go through AutoTuner's Mail-in Unlock service; once unlocked, reading and writing are done directly at the workbench through the ECU connector, with no need to open the unit. Two processor families are covered: Infineon TC377 (MG1CA770) and ST SPC58N (MG1CA920, MG1CA007, MG1CA001).

BitBox · November 5, 2026
Kefico SIM2K-510 — BENCH-CAN module released
BitBox releases a new BENCH-CAN module for the Kia/Hyundai Kefico SIM2K-510 control unit, available through the User Portal or any authorised dealer.

BitBox · November 5, 2026
Yeson 28D-76 (MT05.A) — added to China Yeson Moto/Extreme
BitBox adds support for the Yeson 28D-76 (MT05.A) control unit, used on various brands of Chinese-made motor vehicles, in its China Yeson Moto/Extreme module. The page does not state an access mode (OBD, Bench or Boot).

Autotuner · November 4, 2026
Bosch MED17.1.10 & MED17.1.61 — OBD VR for the VAG Group
AutoTuner extends OBD Virtual Read (VR) coverage to the Bosch MED17.1.10 and MED17.1.61 control units on its AutoTuner One: MED17.1.10 on 2.0 TFSI Audi A4 (2015+) and A5 (2016+), MED17.1.61 on 1.4 TSI/TFSI S&S engines across Audi, Volkswagen, Seat and Skoda. Both run on the AURIX TC1793 processor, with checksum correction and a back-to-stock function; writing takes about 13 minutes.

MagicMotorsport · November 3, 2026
Korhex — Bosch MG1CS011 / MG1CS111 / MG1CS163 (TC298)
Flex version 8.29.0.0 extends Korhex to the Bosch MG1CS011, MG1CS111 and MG1CS163 control units of the Volkswagen group, built on the TC298 processor. These units were already supported through Voltage Fault Injection (VFI); Korhex now unlocks them without working on the PCB, and programming then continues in Bench mode. For the MG1CS163, Flex details: read, write and checksum of the internal flash, read and write of the internal EEPROM, full backup; licence FLS0.20M/S or FLS0.5M/S; about 30 seconds to connect, 2 min 30 s to read and 2 minutes to write. This release also reorganises Flex's protocols into two families — Boot Glitch (VFI-based) and Korhex — and calls for particular attention to pins A1 and A4.

Dimsport · November 2, 2026
Cummins CM2450B — new TheGenius protocol for RAM trucks
Dimsport's TheGenius adds a new protocol for the Cummins CM2450B control unit fitted to RAM 2500, 3500, 4500 and 5500 pickups and heavy-duty trucks (MY2022–2024, 6.7L turbodiesel). TheGenius reads and writes the file independently, with no PC required: the procedure runs entirely on the tool's own screen. Dimsport unveiled the protocol at the SEMA Show in Las Vegas (3–6 November 2026); the page does not state whether the connection is made in OBD, Bench or Boot mode.

Autotuner · November 2, 2026
Bosch MED17.1.21 & MED17.1.27 — OBD VR for the VAG Group
AutoTuner adds OBD Virtual Read (VR) support for the Bosch MED17.1.21 and MED17.1.27 control units on its AutoTuner One, covering 1.4 and 1.0 TSI/TFSI petrol engines across the Audi, Volkswagen, Seat and Skoda range. Both run on the AURIX TC1793 processor, with checksum correction and a back-to-stock function; writing takes about 11 minutes 30 seconds.

Autotuner · October 30, 2026
Delphi 4J (24V)
Autotuner extends its Delphi 4J protocol, already available on 12 V passenger platforms, to 24 V architectures: Isuzu N-Series (2014+) and ELF (2011+) with the 3.0 TD 4JJ1 engine, alongside the 12 V Isuzu D-Max / V-Cross (2006+), MU-X (2013+) and Holden Rodeo (2002+). In the vehicle, the dedicated 24V OBD cable is required and the application asks to confirm the 24 V system before communicating; OBD on Bench keeps working with the standard bench cable. OBD Virtual Read with Normal Read fallback, calibration readout, MPC561 microcontroller, writing about 2 minutes, checksum correction.

BitBox · October 30, 2026
Bosch MG1CS008 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MG1CS008 Gen2 control units from 2020 onwards, built on AURIX TC298 processors and fitted to petrol VAG vehicles, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only.

Autotuner · October 28, 2026
Bosch MED17.2
Autotuner adds Bench Normal Read support for the Bosch MED17.2 control unit (Infineon TriCore TC1796) of the turbocharged Mini range: Cooper S and Clubman (2007 to 2010+) in 1.6 T and 1.6 T JCW with the N14 and N18 engines, Roadster and Coupé (2011+), Countryman (2009+) in 1.6 T JCW and Paceman (2013+) in 1.6 T JCW GP. Readout covers bootloader, software and calibration; reading takes about 1 minute and writing 30 seconds, with checksum correction and backup.

BitBox · October 28, 2026
Continental SIM3K-54x — module released
BitBox's Kia/Hyundai Continental SIM3K-54x BENCH-CAN module is now on sale through the User Portal and authorised dealers. It works with the SIM3K-540, 541, 542 and 543 control units in Bench over CAN; the announcement gives no further detail and refers to the module's catalogue page.

Dimsport · October 27, 2026
EFI E5 — OBD remapping for Fantic Caballero
Dimsport's RACE line adds a new protocol for the EFI E5 control unit of the Fantic Caballero, Euro 5 and Euro 5+. Under the new FLASH_1008 protocol, TheGenius reads and writes the ECU directly through the OBD diagnostic port, with no need to open the unit. Models covered run from 2021 to 2026, with 29.4 kW of power: Caballero Scrambler, Rally and Flat Track.

MagicMotorsport · October 26, 2026
Korhex — Boot Glitch for VAG Bosch MDG1 (TC298 / TC299)
Flex version 8.27.0.0 extends Korhex to the Bosch MDG1 control units of the Volkswagen group built on TC298 and TC299 processors: MG1CS002 H80, MG1CS008, MG1CS031 H80 and MD1CS004 H80 (TC298), and MD1CS014 (TC299). These units were already supported through voltage fault injection (VFI); Korhex now unlocks them without working directly on the PCB, and programming then continues in Bench mode. Memories: read, write and checksum of the internal flash, read and write of the internal EEPROM, full backup. An FLS0.20 Boot Glitch licence or a Flex Full FLS0.5 configuration is required; about 30 seconds to connect, 2 min 30 s to read and 2 minutes to write. Vehicles cited: Audi SQ5 (FY) 3.0 TDI and RS5 (F5) 2.9 V6, Cupra Formentor 2.0 TSI, Lamborghini Urus S 4.0 V8 and Volkswagen Golf VIII 2.0 TDI.

Dimsport · October 26, 2026
MAN Bosch MD1CE100 — unlocking with TheGenius
Dimsport adds plugin 2130 to TheGenius: the Bosch MD1CE100 control units of MAN vehicles are unlocked through an HVR connection, after which work continues in BENCH mode directly on the ECU connector. The ECU equips several models of the MAN range, including the TGX, TGS, TGM and TGL. The announcement is aimed at truck and off-highway professionals; it does not detail the operations available after unlocking.

Autotuner · October 26, 2026
Delphi MT05.B
Autotuner adds 100% OBD Normal Read support for the Delphi MT05.B control unit of Benelli and QJMOTOR motorcycles: Benelli TRK 552 / TRK 552X and Tornado 550 (2024+, 554 cc) and Leoncino Bobber 400 (2026+, 385 cc); QJMOTOR SRT 550 / SRT 550 SX (2023+) and SRK 550 (2024+, 554 cc), 500GS (2024+, 500 cc) and SRV 400 VS (2025+, 385 cc). Calibration readout, S32K144 microcontroller, 15 seconds to read and 15 seconds to write, with checksum correction.

Dimsport · October 23, 2026
Bosch MD1CS004 H80 — new RACE plugin for the VAG group
The RACE line gains a plugin for the Bosch MD1CS004 H80 control units fitted to many Volkswagen group vehicles, opened through the HVR connection method despite the hardware protections that limited traditional reprogramming. Diesel applications announced: Audi 2.0 TDI, 30 TDI and 40 TDI; Cupra 2.0 TDI; SEAT 2.0 TDI; Škoda 2.0 TDI and 2.0 TDI CR; Volkswagen 2.0 TDI, 2.0 TDI.2 and 2.0 TDI GTD. The plugin number is not given; Dimsport refers to its application list and operating manual for the supported vehicles and the available procedures.

Autotuner · October 23, 2026
Keihin 812.41 (KENZ) & 796.41 (KRSZ)
Autotuner adds 100% OBD Normal Read support for the Keihin 812.41 and 796.41 control units of off-road and motorsport motorcycles. The 812.41 covers KTM 250 to 500 EXC-F, SX-F, XC-F, SMR and Freeride 350 (2011 to 2013+), Husqvarna FC, FE and FS (2014 to 2015+) and Husaberg FE, FS and FX (2009 to 2013); the 796.41 covers KTM (2017 to 2024+, including the 450 Rally Replica and the RC4 R), Husqvarna (2017 to 2024+, including the FR 450 Rally) and GasGas EC, MC, EX, ES and RX (2021 to 2024+). The KTM M3C / Keihin OBD cable is required at the diagnostic connector. Software and calibration readout, KT2021 and KT2022 microcontrollers, reading about 2 min 15 s and writing 1 min 15 s, with checksum correction.

BitBox · October 23, 2026
Bosch MD1CE101 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MD1CE101 Gen2 control units from 2020 onwards, built on AURIX TC299 processors and fitted to diesel trucks and industrial vehicles, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only.

Autotuner · October 21, 2026
Keihin RH850
Autotuner adds Honda Euro 5 motorcycles through the Keihin RH850 control unit, in 100% OBD Normal Read: from the CBR1000RR-R Fireblade to the Africa Twin 1100, the CB750 Hornet and the X-ADV 750. A model-specific cable is required. Readout covers bootloader, software and calibration; reading takes about 10 minutes and writing 3 min 15 s, with checksum correction. The announcement names only those four models; the full list is in the tool's compatibility list.

MagicMotorsport · October 19, 2026
Korhex — Boot Glitch for Bosch MD1CS069 / MD1CS089 (TC299)
Flex version 8.26.0.0 extends Korhex to the Bosch MD1CS069 and MD1CS089 control units on TriCore TC299 processors fitted to commercial and industrial vehicles. The Boot Glitch is performed without working on the PCB: a mask described in the manual locates the glitch point and positions Korhex; once connected, the technician either keeps working in Boot Glitch or unlocks the unit and continues in Bench. Memories: read, write and checksum of the internal flash, read and write of the EEPROM, full backup. An FLS0.20 Boot Glitch licence or a Flex Full FLS0.5 configuration is required; about 30 seconds to connect and glitch, 2 min 30 s to read and 2 minutes to write. Vehicles cited: Fiat Ducato 2.2 MultiJet III, DR PK8 2.0 Turbo, John Deere 5G (5115G), Massey Ferguson MF 3xx and New Holland T5 Series II, all 3.6 L. The changelog reports a more reliable Boot Glitch connection.

Autotuner · October 19, 2026
Delphi DCM3.7AP / DCM6.2AP
Autotuner adds 100% OBD Normal Read support for the Delphi DCM3.7AP and DCM6.2AP control units of Chinese SUVs, pickups and off-roaders. DCM3.7AP: Great Wall Hover 5 / H5 (2013+), Steed (2013+) and Wingle (2010+) and Haval H6 (2011+), all 2.0 TD GW4D20. DCM6.2AP: Haval H6 (2017+, GW4D20D) and H9 (2014+, GW4D20T), JAC T6 (2015+) and T8 (2020+) 2.0 diesel, BAIC BJ40 (2014+) 2.0d. Calibration readout, SH72513 and SPC5674 microcontrollers, reading about 6 minutes and writing 5 min 30 s, with checksum correction. The source's own title spells the maker “Deplhi”.

BitBox · October 16, 2026
Delphi MT05.9
BitBox adds the Delphi MT05.9 control units, used by various brands of Chinese-made vehicles, to its Delphi MT05 module, the oldest in its catalogue. The announcement does not state the access mode and refers to the module's catalogue page.

Autotuner · October 14, 2026
Delphi DCM7.1AP / DCM7.24
Autotuner adds 100% OBD Normal Read support for the Delphi DCM7.1AP and DCM7.24 control units of light commercial vehicles, pickups and light trucks. DCM7.1AP: Great Wall POER, Haval and Wingle (2.0 TD GW4D20M / GW4D20D), Isuzu 100P, KV100, KV600, NKR and Taga / Taga H (3.0 TD), JAC T8 Pro and T9 (2.0 CTI), Dongfeng Rich and Captain (2.3 and 2.4 TD), Changan Hunter F70 (2.0 TD) and JMC Yuhu (2.0 and 2.8 TD). DCM7.24: Foton Tunland, Toano and View (2.4 TD), Aumark, Forland and Ollin (4.2 and 4.3 TD). Calibration readout, TC277 microcontroller, reading about 2 min 45 s and writing 3 minutes, with checksum correction.

Autotuner · October 14, 2026
TRW EMS2.3 / EMS2.4
Autotuner adds Bench Normal Read support for the TRW EMS2.3 (SPC5674) and EMS2.4 (SPC5777M) control units of Volvo and Renault Euro 6 trucks: Volvo FH, FM and FMX with the D13K engine, Renault T, C, K and D series with the DTI11 and DTI13, plus Volvo Penta and industrial, agricultural and forestry engines. The ATUBC130 bench cable is required; reading takes about 10 minutes and writing about 2, with checksum correction, backup and datalogs for boost, torque, fuelling and injection timing.

BitBox · October 14, 2026
Bosch MD1CS069 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MD1CS069 Gen2 control units from 2020 onwards, built on AURIX TC299 processors and fitted to diesel light commercial vehicles, trucks and industrial machinery, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only. Note that the title says MD1CS069 while the body reads MG1CS069; the announcement does not explain the difference.

Dimsport · October 14, 2026
Race — new applications, release 194
Dimsport releases a new batch of Race plugins, available only on The Genius platform. Among them: Bosch EDC16C42 (MPC56x) in Bench for the Chevrolet Express and GMC Savana 6.6 L, Bosch MEG17.9.22 (TC1724) in Bench for the Hyundai i20 1.4, Marelli 11RZ (TC277) in Bench for the Moto Morini X-Cape 1200, Siemens SIRIUS32N and TA2000 (ST10) for Renault/Dacia and the PSA gearbox, Keihin and Denso (SH7055) for the Honda Accord 2.4, Yamaha YZF-R6 and Suzuki SV 1000, Mitsubishi MH8115F and MH501DF for the Yamaha Kodiak 700 and Suzuki Raider R150, Mitsubishi MH8611 for the Kawasaki Jet Ski Ultra 310R, and Caterpillar ADEM III (MPC555) and A6M12 (MPC5777C) for the 966K loader and 308, 309 and 310 excavators. The full list is in the PDF linked from the announcement.

Autotuner · October 13, 2026
MyFlasher 2.8.0
MyFlasher 2.8.0 is out on iOS and Android. Clients can now open the datalogs received in their chat as interactive measurement curves, choose the parameters displayed, zoom into an RPM range and read exact values; until now only the tuner could inspect those recordings. The update also speeds up the link with the One device, up to 10 times faster over Bluetooth and 2 to 5 times over Wi-Fi according to Autotuner.

Autotuner · October 12, 2026
Bosch MED17.4 (TC1796)
Autotuner adds 100% OBD Normal Read support for the Bosch MED17.4 control unit (TC1796) of the 1.6 THP turbo petrol engine, fitted from 2005 to 2018 to Peugeot 207, 208, 308, 408, 508, 3008, 5008 and RCZ, Citroën C4, C4 Picasso, C4 SpaceTourer, C4 AirCross, C5, DS3, DS4 and DS5, the DS 3, DS 4 and DS 5, and the 2017 Opel/Vauxhall Grandland. Reading takes about 1 min 15 s and writing about 30 s, with checksum correction.

Autotuner · October 9, 2026
Continental EMS10 — BETA
Autotuner opens the Continental EMS10 (CEM1) control unit, built on an MPC5777C, in 100% OBD Normal Read, in BETA. The 24V OBD cable is required. The announcement lists Scania R series (2018+) with the 16.4 L DC16 V8 and S series (2015 to 2018+) with the 12.7 L DC13 and the 16.4 L DC16, under a heading that still reads Motorola EMS S6 & Continental EMS S8. Reading takes about 7 minutes and writing 9 min 45 s, with checksum correction; Autotuner asks workshops for feedback on this beta.

BitBox · October 9, 2026
Bosch MG1CS031 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MG1CS031 Gen2 control units from 2020 onwards, built on AURIX TC298 processors and fitted to VAG petrol vehicles, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only.

Autotuner · October 7, 2026
Motorola EMS S6 & Continental EMS S8 — BETA
Autotuner adds the Motorola EMS S6 and Continental EMS S8 (EMD1) control units in 100% OBD Normal Read, in BETA: Scania trucks from Euro 3 to Euro 6, series 4 (P124, R124, T124) with the 11.7 L PDE and HPI, P, G, R and S series from 8.9 to 15.6 L (DC13, DC16 V8), Scania DC09 and DC16 agricultural and industrial engines, and Doosan/Develon DX380 LC-7 and DX530 LC-7 excavators, DL420 and DL450 loaders and the MT31 dumper. MCUs MPC555 and MPC5566; the 24V OBD cable is required in the vehicle, the Scania S6/S8 bench cable on the bench.

MagicMotorsport · October 7, 2026
Korhex — Boot Glitch for Porsche Bosch MG1CP007 / MG1CS047
Flex version 8.25.0.0 adds a Boot Glitch procedure with Korhex for the Porsche Bosch MG1CP007 and MG1CS047 control units built on a TC299, already supported through voltage fault injection (VFI). Korhex reaches the processor without removing components from the unit; once unlocked, programming continues in Flex's Bench mode. An FLS0.20 Boot Glitch licence or a Flex Full FLS0.5 configuration is required. Vehicles cited: Porsche 911 Carrera, Carrera S, GT3 and Turbo of the 992.1 generation, 2021 model year.

BitBox · October 7, 2026
Bosch MG1CS111 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking, followed by bench operation, for locked Bosch MG1CS111 Gen2 control units from 2020 onwards, built on AURIX TC298 processors and fitted to VAG petrol vehicles, in its Bosch MG1/MD1 Gen2 BENCH module, SM2 and SM3 interfaces only.

Dimsport · October 5, 2026
Race — new applications, release 193
Dimsport releases a batch of Race plugins, available only on The Genius platform, centred on Bosch MDG1 units in Bench: MD1CS003 and MG1CS042 (Stellantis), MG1CS031 and MD1CS011 (VAG), MD1CP017 and MD1CP007 (Land Rover), MD1CS005 and MD1CP006 (Ford), MD1CS069 (FCA light commercials, CNH, Landini, McCormick, Carraro, John Deere, Massey Ferguson), MD1CS089 (Deutz) and MD1CE101 (CNH, FPT, Iveco), plus plugin 165 for Bosch MDG1 in HVR mode, all brands, which requires tgOS 3.2.0.0, firmware 1.9.0.0.0, opening the unit, removing a resistor and the F36TG108 adapter cable.

Autotuner · October 5, 2026
Bosch VC1CP010
Autotuner adds Bench mode support for the Bosch VC1CP010 control unit, covering the electric and hybrid platforms of Renault, Alpine, Dacia, Nissan and Mitsubishi. It opens the 6AK electric motor (Renault 4 and 5 E-Tech) and the 6AM (Alpine A290, Megane and Scenic E-Tech), whose identical hardware is sold at outputs from 95 to 220 hp.

MagicMotorsport · October 5, 2026
Keihin KTKSv2 — OBD programming (Triumph)
Flex version 8.24.0.0 adds OBD write support for the Keihin KTKSv2 control unit, built on an RH850 microcontroller and fitted to Triumph motorcycles. Writing is performed through the diagnostic port, without removing or opening the unit. MagicMotorsport notes that the FLX2.68 connector may be required depending on the application.

Autotuner · October 2, 2026
Denso VEA Gen2 (SPC5777M)
Autotuner announces Bench support for the Denso VEA Gen2 family built on the SPC5777M processor, which equips Volvo VEA engines and had remained unreadable since late 2017. The release also adds an OBD patch available after a one-time Bench unlock.

BitBox · October 2, 2026
Bosch MG1CA811
BitBox adds VAG petrol vehicles fitted with the Bosch MG1CA811 control unit, based on an SPC58 microcontroller, to its Bosch MG1/MD1 BENCH module. The announcement restricts support to the SM2 and SM3 interfaces.

Autotuner · September 30, 2026
Siemens SIMTEC71
Autotuner supports the Siemens SIMTEC71 in 100% OBD Normal Read, on the naturally aspirated petrol platforms of Opel, Vauxhall and Subaru: Astra, Corsa, Tigra and Vectra 1.8i Ecotec, Omega and Zafira 2.2i, and the Subaru Traviq 1.8i Ecotec. The unit is built on a C167 microcontroller.

Autotuner · September 30, 2026
Continental EMS2211 / EMS2301 / EMS2302 / EMS2701
Autotuner supports four Continental units in 100% OBD Normal Read across the Ford and Lincoln ranges: EMS2301 and EMS2302 on the Ka 1.0 TiVCT and 1.2 Ti-CVT, EMS2211 on the B-Max, Fiesta, Focus and EcoSport 1.5, 1.6 and 2.0 Duratec as well as the C-Max, Mondeo and Lincoln MKZ 2.0 HEV, and EMS2701 on the Kuga/Escape, Maverick and Galaxy 2.5 FHEV and PHEV and the Lincoln Corsair 2.5 PHEV.

Dimsport · September 29, 2026
Memobike — software release 59
Dimsport publishes version 59.0.0 of the Memobike software, adding new models and extending diagnostics to further control units on models already covered.

MagicMotorsport · September 28, 2026
Korhex — Boot Glitch for Stellantis Bosch MD1CS003
Flex performs Boot Glitch on Stellantis Bosch MD1CS003 ECUs (TC298 processor) with Korhex and EMFI, then programs them in Bench mode. Unlike the VFI procedure already available, nothing has to be removed from the unit. The F mask is required, and the release also makes the STL files of the positioning masks downloadable. An FLS0.20 Boot Glitch licence, or the Flex Full FLS0.5 configuration, is needed.

Autotuner · September 28, 2026
BMW DME8 — MD1CP002 / MD1CS001 / MG1CS003
Autotuner supports Bosch MD1CP002, MD1CS001 and MG1CS003 ECUs (SPC5777M microcontroller) on BMW Group platforms directly in Bench mode, removing the Mail-in Unlock step.

Autotuner · September 25, 2026
Bosch MG1CS018
Autotuner adds the Bosch MG1CS018 ECU in 100% OBD Virtual Read, on American trucks, SUVs and high-output V6 EcoBoost powertrains.

Autotuner · September 25, 2026
Bosch MG1CS080
Autotuner adds the Bosch MG1CS080 ECU in Bench mode, on the Geely / Volvo CMA platform.

MagicMotorsport · September 25, 2026
Bosch MG1CS032 — Boot Glitch with Korhex
Flex 8.22.0.0 opens Boot Glitch access to Stellantis Bosch MG1CS032 ECUs on SPC58 processors, using Korhex and EMFI technology.

Dimsport · September 24, 2026
HVR Mode — unlocking Bosch MDG1
Dimsport announces HVR Mode for a selection of post-2021 Bosch MDG1 ECUs on protected INFINEON AURIX TC298TP/TC299TP microcontrollers. It requires the new HVR adapter cable, a two-point connection in BOOT (OPEN mode) and the temporary removal of one resistor. The source announces availability for the following week, without a date; the page title is in Italian while its body is in English.

Autotuner · September 23, 2026
Bosch EDC17CV54
Autotuner adds the Bosch EDC17CV54 ECU in 100% Bench Normal Read, on agricultural, construction and forestry equipment — AGCO, JCB, John Deere, Yanmar and others.

MagicMotorsport · September 23, 2026
BMW Bosch MG1CS003 locked — Bench programming
Flex 8.21.0.0 programs locked BMW Bosch MG1CS003 ECUs directly in Bench mode, without opening the ECU or unlocking it by Boot Glitch. The announcement summary writes SCP5777M where its body writes SPC5777M.

BitBox · September 23, 2026
Bosch MD1CS012 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking then bench operation for locked Bosch MD1CS012 Gen2 2020+ ECUs on AURIX TC298, used on Kia and Hyundai diesels, in its Bosch MG1/MD1 Gen2 BENCH [SM2/SM3 ONLY] module.

BitBox · September 18, 2026
Bosch MG1 / MD1 Gen2 — BSL / Bench
BitBox adds BSL-mode unlocking then bench operation for locked Bosch MG1/MD1 Gen2 2020+ ECUs on AURIX TC29x, across petrol and diesel vehicles of several makes. The source states that other ECU types will follow.

BitBox · September 18, 2026
AECS FC-54 (Chery)
BitBox adds support for AECS FC-54 ECUs, built on NXP SPC563M64 microcontrollers and used on Chery petrol vehicles, in its China Delphi/AECS Petrol module.

Autotuner · September 18, 2026
Continental EMS2204 / EMS2205 / EMS2208
AutoTuner now supports the Continental EMS2204, EMS2205 and EMS2208 engine ECUs in 100% OBD Normal Read and write (TC1738/TC1766, checksum correction). Coverage targets Ford petrol and hybrid models — B-Max, C-Max, EcoSport, Fiesta, Focus, Mondeo — plus the Lincoln MKZ 2.0 HEV.

BitBox · September 16, 2026
Motion SE07
BitBox adds support for Motion SE07 ECUs, used on various brands of Chinese-made motor vehicles, in its China Motion Moto/Extreme module.

Autotuner · September 16, 2026
Suzuki MH8115F
AutoTuner adds the Mitsubishi MH8115F ECU in 100% OBD Virtual Read on Euro 5 Suzuki motorcycles and scooters: AN 400 Burgman/Skywave, DL 650 V-Strom and SV 650 from 2021. The Euro 5 6-pin motorcycle OBD cable is required.

MagicMotorsport · September 16, 2026
Exclusive: OBD for Stellantis EVPT VCU3000
Flex 8.20.0.0 adds exclusive OBD support for Stellantis EVPT VCU3000 units (TC234L) fitted to the group's electric city cars — Citroën AMI, Fiat Topolino, Opel Rocks-e — in Virtual Read from the diagnostic port, with map write and checksum. The unit no longer has to be opened or removed. OBD joins the Bench and Boot modes already available.

Autotuner · September 15, 2026
Continental EMS2101 / EMS2102 / EMS2103 / EMS2106
AutoTuner adds the Continental EMS2101, EMS2102, EMS2103 and EMS2106 ECUs in 100% OBD Normal Read and write (C167, checksum correction), aimed at Ford naturally aspirated petrol engines: B-Max 1.4i 16v, Fiesta 1.25i Duratec 16v and 1.6i Ti-VCT, Mondeo 1.6i Ti-VCT.

BitBox · September 11, 2026
Yeson 28D-96
BitBox adds support for Yeson 28D-96 ECUs, used on various brands of Chinese-made motor vehicles, in a brand-new module called China Yeson Moto/Extreme.

Autotuner · September 11, 2026
Bosch MD1CE100 / MD1CE101
Bench Normal Read and write for the Bosch MD1CE100 (TC299 + TC389) and MD1CE101 (TC299) ECUs, with checksum correction, backup and a required Mail-in Unlock. Coverage spans trucks (MAN TG, Ford F-MAX/Cargo, VW Constellation/Meteor, Shacman, Sinotruk, Kamaz), agricultural machinery (Fendt, Case IH, New Holland, Steyr, Claas) and construction equipment (Doosan/Develon, Case Construction, Zoomlion, Dieci, Faresin, Horsch).

Autotuner · September 10, 2026
Bosch MG1CS032
Bench Normal Read and write for the Bosch MG1CS032 ECU (SPC58N), with checksum correction, backup and a required Mail-in Unlock. It covers the Stellantis 1.2 PureTech/Turbo petrol engine: Peugeot 208, 2008 and 301, Citroën/DS DS 3 Crossback, Opel/Vauxhall Corsa and Mokka.

Autotuner · September 9, 2026
Motion DE08 / FE08 / FE08.02 / SE08 / MT05.C
The whole Motion ECU family (DE08, FE08, FE08.02, SE08, MT05.C) is added in 100% OBD Normal Read and write (SPC572L64, checksum correction), for two-wheelers and light vehicles from QJMOTOR, Benda, Zontes, KL Motorcycles, Keeway, RKS Motor, Hyosung, Romet and Togo Motosiklet.

BitBox · September 8, 2026
BMW Bosch MG1/MD1 SPC5777, 2020 onwards
BitBox adds Bench support for Bosch MG1/MD1 units built from 2020 onwards on the NXP SPC5777 microcontroller, for petrol and diesel BMW and Mini. It lands in the Bosch MG1/MD1 Gen2 BENCH module, which works with Scanmatik SM2/SM3 interfaces only.

Autotuner · September 8, 2026
Bosch MD1CS069 / MD1CE101 — BETA
Released in BETA: Bosch MD1CS069 and MD1CE101 in 100% OBD Normal Read and write (TC299, bootloader + software + calibration readout, checksum correction). It covers agricultural, construction and heavy-duty machinery from Case IH, Case Construction, New Holland, Claas, Deutz-Fahr, Same, Lamborghini, Steyr, Landini, McCormick and Massey Ferguson.

MagicMotorsport · September 8, 2026
Mercedes Truck CPC5 after 2020, with Korhex
Flex 8.18.0.0 adds Mercedes Truck Bosch CPC5 units (SPC58) on vehicles built after 2020, worked in Boot Glitch with Korhex — the hardware extension driven by Flex — using EMFI (electromagnetic fault injection). Read/write/checksum of the internal flash, read/write of the internal EEPROM and full backup, on Actros and Arocs among others. FLS0.20 licence or Flex Full FLS0.5 required.

MagicMotorsport · September 8, 2026
Korhex: direct MCU access for ECU programming with Flex
A presentation of the tool rather than a vehicle release. Korhex is a hardware extension for the Flex programmer that reaches a contact point on the microcontroller of supported ECUs during unlocking and Boot Glitch procedures, using EMFI. It is not a standalone programmer — Flex drives the whole sequence — and it removes traditional Boot preparation such as desoldering a resistor or wiring Boot pins by hand. Flex Full (FLS0.5M/S) or Flex Boot Glitch (FLS0.20M/S) required.

Autotuner · September 7, 2026
Bosch EDC15C6 / EDC15C6.5-70
Bosch EDC15C6 and EDC15C6-5.70 are added in 100% OBD Normal Read and write (C167, checksum correction), covering Mercedes-Benz CDI diesels: C-Class W203 including the C 30 CDI AMG, CLK C209, E-Class W210/W211, S-Class W220, G-Class W463, ML W163, plus the Sprinter and Viano vans.

PCMflash · September 6, 2026
PCMflash 1.5.0
PCMflash 1.5.0 extends three bootloader modules. Module 92 (Bosch MD1/MG1 Bootloader) now covers BMW MD1/MG1 units built after mid-2020 on SPC5777M and TC29x, with reading, writing, unlocking and flash checksum correction. Module 82 adds two 7DCT300 gearbox variants, and module 86 adds the EAST80.C1 unit of Jetour vehicles with DF727 transmissions.

BitBox · September 4, 2026
Bosch PDCU8.0
BitBox adds Bench support for Bosch PDCU8.0 ECUs built on the Infineon Aurix TC389 microcontroller, on Chinese petrol vehicles. It lands in the first-generation Bosch MG1/MD1 BENCH module, for Scanmatik SM2/SM3 interfaces only. No vehicle brand is named in the announcement.

Autotuner · September 4, 2026
Bosch ECS1049
Bench Normal Read and write for the Bosch ECS1049 ECU (TC399), with checksum correction and backup. It targets the Euro 7 BMW M S58 engine with « BMW M Ignite » technology: M3 (G80/G81) and M4 (G82/G83) from July 2026, M2 (G87) from August 2026 — replacing the earlier Bosch MG1CS049.

MagicMotorsport · September 4, 2026
Mercedes MDG1: Boot Glitch with Korhex
Flex 8.17.0.0 opens Boot Glitch on Mercedes Bosch MD1CP001 and MG1CP002 units (SPC5777) through Korhex and EMFI: no soldering on the PCB, no components removed. Read/write/checksum of the internal flash, read/write of the internal EEPROM and full backup. FLS0.20 licence or Flex Full FLS0.5 required.

Autotuner · September 3, 2026
Continental M3D
Continental M3D ECUs are added in 100% OBD Virtual Read, with write and checksum correction (MPC5534), using the Ducati 4-pin OBD cable. Covered Ducati models: Hypermotard 950 / 950 SP, Monster 821, Monster 1200 / 1200S / 1200R, SuperSport / SuperSport S and Scrambler 1100.

Autotuner · September 2, 2026
BMW DME8: improved OBD Unlock Patch
Not a new protocol but an improved OBD Unlock Patch for BMW DME8 ECUs (Bosch MG1CS024, MG1CS049 and MG1CS201, all TriCore TC298). It prevents the FSC-related DTCs (1B2904, 1F2102, sometimes 021204 / 21B210) raised when flashing modified files. Applying it requires a new Bench unlock, even on an ECU already unlocked with an earlier version.

MagicMotorsport · September 2, 2026
SPC58N unlock with Korhex
Flex 8.16.0.0 extends Korhex to the new-generation SPC58N microcontrollers, with a dedicated Boot Glitch procedure for the BRP Bosch MG1CA920 unit used on Rotax engines. No resistor to remove, no Boot point to solder by hand. Read/write/checksum of the internal flash, read/write of the internal EEPROM and full backup. FLS0.20 licence or Flex Full FLS0.5 required.

Autotuner · September 1, 2026
Bosch ECM4
Bosch ECM4 ECUs are added in 100% Bench Normal Read and write (TC299, checksum correction, backup). Coverage targets 13-litre Euro 6 truck engines: Renault Trucks DTI13 (C, D, K and T), Volvo Trucks D13K (FH New Generation, FMX) and Mack Trucks MP8 (Anthem, Pinnacle).

Dimsport · September 1, 2026
Bosch ECM4 in Bench mode
The Genius now works the Bosch ECM4 engine ECUs in Bench, through the unit's connector and without opening it. Coverage targets heavy trucks built since 2022: Volvo Trucks FH / FH Aero and FM, Renault Trucks T / T High and C, Mack Trucks Anthem and Pinnacle.

Dimsport · September 1, 2026
Bosch MD1/MG1 for BMW and MINI: complete RACE settings
Alongside the new Bench release, Dimsport publishes comprehensive RACE setting files for the Bosch MD1 and MG1 units of BMW and MINI, opening a wider range of maps and parameters for calibration. Listed applications include the BMW M3 (G80/G81), M4 (G82/G83), M2 (G87), M240i (G42), 340d (G20/G21), X5 (G05) and 320d (G20/G21). This is a calibration addition, not a new access mode.

Autotuner · August 31, 2026
Continental M3C (Ducati)
Continental M3C ECUs are added in 100% OBD Normal Read and write (MC9S12, checksum correction), using the Ducati 4-pin OBD cable. Covered Ducati models: Hypermotard 1100 Evo, Monster 1100 Evo, Monster 659, 796 ABS and 797, Scrambler 800 (Icon, Full Throttle, Café Racer, Desert Sled) and Scrambler Sixty2.

MagicMotorsport · August 31, 2026
DAF Delphi ETC3 UDS with Korhex
Flex 8.15.0.0 lets Korhex unlock DAF Delphi ETC3 UDS units (MPC5566) in Boot Glitch, in the workshop — the unit no longer has to be shipped to MagicMotorsport's laboratories through the RFT service. Once unlocked: read/write/checksum of the internal flash, read/write of the external flash and full backup. FLS0.20 licence or Flex Full FLS0.5 required.

Autotuner · August 28, 2026
Bosch MEVD17.2.x
Bosch MEVD17.2.2 (TC1796/TC1797), MEVD17.2.7 and MEVD17.2.9 are added in 100% OBD Virtual Read and write, with no ECU removal, checksum correction and a back-to-stock function. Coverage: MINI N14/N18 1.4 DFI, 1.6 DFI and 1.6 Turbo (R55-R61, 2007-2014) and BMW 28i N20 2.0T (2, 3, 3 GT, 4, 4 Gran Coupé, 5, 5 GT, X3, X4, X6, 2009-2014).

Dimsport · August 28, 2026
Bosch MDG1: new Bench solution for BMW and MINI
A new Bench solution lets The Genius reach the contents of Bosch MDG1 units on BMW and MINI and carry out programming operations without opening the ECU. Supported units: Bosch MD1CP032 (TC299), MD1CS001 (TC298), MG1CS024 (TC298), MG1CS049 (TC298) and MG1CS201 (TC298).

Autotuner · August 27, 2026
New Console Export & Clear features
A software feature release rather than a protocol: the AutoTuner software gains one-click console log export on every operation (Ident, Read, Write), automatic file naming from the vehicle VIN when available, and a « Clear Console Log » button.

BitBox · August 26, 2026
Magneti Marelli 11RZ
BitBox adds support for Magneti Marelli 11RZ ECUs, built on Infineon Aurix TC277 microcontrollers and fitted to the Moto Morini X-CAPE 1200, in its Magneti Marelli BENCH-CAN module — bench access over CAN.

Autotuner · August 26, 2026
Delphi DCM3.2AP
The Delphi DCM3.2AP ECU is added in 100% OBD mode, Normal Read and write (MPC563, checksum correction), with no ECU removal. It covers the Kia 2.9 CRDi Euro 4 diesel engine in the Kia Bongo (2014+) and the Kia Carnival / Sedona (2005+).

MagicMotorsport · August 25, 2026
BMW Marelli MBC1 and MBC2 in Bench
Flex 8.14.0.0 adds Bench support, worked directly by pinout, for Marelli MBC1 and MBC2 units (XC20xx) fitted to BMW Motorrad and Husqvarna motorcycles, with full read of the unit's content. Read/write/checksum of the internal flash, read/write of the external EEPROM and full backup, under FLS0.1M/S, FLS0.13M/S or FLS0.5M/S licences.

Autotuner · August 24, 2026
Marelli 9GV
The Marelli 9GV ECU is added in Bench mode, Normal Read and write (SPC563M64, checksum correction, backup). It covers Volkswagen 1.6 Flexfuel and 1.6 MSI models sold in LATAM and export markets: Fox, CrossFox, Gol, Saveiro, Voyage, SpaceFox, Vento and Jetta.

Autotuner · August 21, 2026
Siemens MS42
The Siemens MS42 ECU is added in 100% OBD Normal Read and write (C167 / 29F400, checksum correction), with no ECU removal. It covers the BMW M52TU double-VANOS straight-six: 3 Series E46 (320i, 323i, 328i), 5 Series E39 (520i, 523i, 528i), 7 Series E38 (728i) and Z3 2.0 / 2.3 / 2.8.

MagicMotorsport · August 20, 2026
VAG Bosch MG1CS111 TC298 without RFT
Flex 8.13.0.0 makes the VAG Bosch MG1CS111 (TriCore TC298) workable without shipping: Boot Glitch unlocking in the workshop, then work in Bench — no RFT mail-in to MagicMotorsport's laboratories. Boot unlock, read/write/checksum of the internal flash, read/write of the internal EEPROM and full backup, on Audi, Cupra, Škoda and Volkswagen 2.0 TSI. Flex Full Master (FLS0.5M) or Slave (FLS0.5S) licence required.

Autotuner · August 19, 2026
Bosch MSE9.0
The Bosch MSE9.0 ECU is added in Bench mode, Normal Read (TC375, read in one minute, write in 45 seconds, automatic checksum correction and backup). It covers latest-generation Powersports vehicles including the CFMOTO 1000 MT-X and 675 SR-R (A2 version included), plus flagship models from Loncin, Voge, Zontes and ZXMOTO.

BitBox · August 14, 2026
BMW Bosch MG1/MD1 TC29x, 2020 onwards
BitBox opens a new module, Bosch MG1/MD1 Gen2 BENCH, for Bosch MG1/MD1 units built from 2020 onwards on petrol and diesel BMW and Mini, with Scanmatik SM2/SM3 interfaces only. Note that the announcement contradicts itself on the microcontroller: its title says Aurix TC29x, its body says TC28x.

Autotuner · August 14, 2026
BMW DDE8/DME8 in Bench (No Mail-in Unlock)
The Bosch DDE8 and DME8 ECUs (BMW) are now supported in Bench read/write on AutoTuner, no mail-in unlock required.

MagicMotorsport · August 13, 2026
BMW & Mini MDG1: work in Bench
Flex 8.12.0.0 introduces a world-first solution for the latest-generation Bosch MDG1 units on BMW & Mini, everything stays in the workshop, in Bench.

MagicMotorsport · August 10, 2026
Ford Bosch MD1CP061 No RFT
Flex 8.11.0.0 adds Ford Bosch MD1CP061 via Boot Glitch then Bench, unlock and finish in the workshop, no RFT.

Autotuner · August 3, 2026
Bosch EDC15C7 (GM) - BETA
The Bosch EDC15C7, fitted to many early-2000s General Motors vehicles, is now supported on AutoTuner in BETA.

MagicMotorsport · July 31, 2026
Stellantis EVPT VCU3000 in Bench
Flex 8.10.0.0 lets you fully back up the EVPT VCU3000 on Stellantis EVs via pinout, no Boot needed.

Autotuner · July 31, 2026
Bosch Mx7.9.5x
The Bosch Mx7.9.5x family (M7.9.5, ME7.9.5…), the ultimate city cars, is now supported on AutoTuner.

Autotuner · July 29, 2026
Aisin AL1000 (VAG)
The Aisin AL1000 automatic gearbox TCU (VAG) is now supported via OBD Virtual Read on AutoTuner.

MagicMotorsport · July 29, 2026
Honda Keihin 38770-Mxx in OBD Full & Bench
A new exclusive Flex solution for Honda Keihin 38770-Mxx (RH850) units, now programmable in OBD Full.

Autotuner · July 28, 2026
New Backup File Tool (BETA)
AutoTuner launches its Backup File Tool in BETA, now available to the whole community on AT Cloud.

Autotuner · July 27, 2026
Aisin AQ450 (VAG)
The Aisin AQ450 automatic gearbox TCU (VAG) is now supported via OBD Virtual Read on AutoTuner.

Autotuner · July 24, 2026
Bosch MG1CS202 / MG1CS203
The latest-generation Bosch MG1CS202 and MG1CS203 ECUs are now supported on AutoTuner.

MagicMotorsport · July 24, 2026
MAN Bosch MD1CE100 TC299 No RFT
Flex 8.8.0.0 brings new-generation MAN Bosch MD1CE100 industrial-vehicle ECUs into the fold, no RFT.

Autotuner · July 22, 2026
Bosch MD1CP062 - Ford Ranger Super Duty
AutoTuner extends its 100% OBD protocol for Ford Bosch MD1CP062 to the new Ford Ranger Super Duty.

MagicMotorsport · July 22, 2026
Toyota Denso Gen2 in Bench
Flex 8.7.0.0 adds Bench programming for Toyota Denso Gen2 units on 2.4L and 2.8L diesels.

Autotuner · July 20, 2026
Denso P5.0SC
The Denso P5.0SC ECU is now officially supported on AutoTuner.

Autotuner · July 17, 2026
Bosch MD1CS015/MD1CS115
The Bosch MD1CS015 and MD1CS115 (DDE9), latest-generation diesel ECUs, are now supported in Bench mode.

MagicMotorsport · July 16, 2026
VAG Bosch MG1CS011 TC298 No RFT
Flex 8.6.0.0 adds the VAG Bosch MG1CS011 (TC298) to Boot Glitch mode, then Bench programming: everything stays in the workshop, no RFT.

Autotuner · July 15, 2026
Bosch MG1CS221
The Bosch MG1CS221 (DME9), the ECU of the most exclusive prestige segment, is now officially supported.

Autotuner · July 14, 2026
MyFlasher 2.7.0
MyFlasher 2.7.0: a major update to the mobile app that goes with the One, with a reworked experience.

MagicMotorsport · July 14, 2026
Improved Boot Glitch Protocols
Flex 8.5.0.0 brings solid improvements to Boot Glitch mode on Bosch units with TC2xx processors: simpler, faster and more reliable in the workshop.

Autotuner · July 13, 2026
Sagem S2000
The Sagem S2000, a cornerstone of the Renault lineup from 1998 to 2012, joins the tool: French youngtimers are covered.

Autotuner · July 10, 2026
Mitsubishi M32R
The Mitsubishi M32R, the ECU behind Ducati's finest superbikes, is now supported via OBD.

Autotuner · July 9, 2026
Bosch MD1CP010 / MD1CP011 / MG1CS046 / MG1CS100
A massive Bench wave: the latest-generation Bosch ECUs of the modern Mercedes-Benz lineup (MG1CS046, MG1CS100, MD1CP010, MD1CP011) join the Autotuner tool.

MagicMotorsport · July 9, 2026
VAG Bosch MD1CS014 TC299 No RFT
Flex 8.4.0.0 opens VAG Bosch MD1CS014 (TC299) units to Boot Glitch mode: handled in the workshop, no shipping, no RFT service.

Autotuner · July 8, 2026
Bosch MG1CP777 / MG1CS701
The Bosch MG1CS701 (MRG5) and MG1CP777 (MRG4) fitted to recent everyday Mercedes models are now officially supported.

Autotuner · July 7, 2026
Bosch MG1CP004
The Bosch MG1CP004 (MRG1PI), the ECU of the latest Mercedes-AMG models from Affalterbach, joins the Autotuner protocol list.

Autotuner · July 6, 2026
Bosch MG1CP003
Autotuner adds support for the Bosch MG1CP003 (MRG1V8), the ECU behind Germany's most exclusive V8 engines.

MagicMotorsport · July 6, 2026
MG1CS049 & MD1CS089 Unlock No RFT
Flex 8.3.0.0 extends Boot Glitch mode: BMW Bosch MG1CS049 (TC298) and Isuzu MD1CS089 (TC299) can be programmed in the workshop, no shipping, no RFT service.

Autotuner · July 3, 2026
Bosch EDC17C87
The Bosch EDC17C87 is now supported in Bench mode: Autotuner widens its off-highway and agricultural coverage.

MagicMotorsport · July 3, 2026
Porsche MDG1 TC2xx No RFT: More and More Compatibilities
With Flex 8.2.0.0, the Bosch MDG1 family with Aurix TC2xx processors manageable in Boot Glitch keeps growing, Porsche first in line.

Autotuner · July 2, 2026
Bosch MG1CS211
Support arrives for Bosch MG1CS211 ECUs, at the heart of today's hybrid drivetrains.

Autotuner · July 1, 2026
Bosch MD1CS014 / MD1CS064
Bosch MD1CS014 (gen 2 included) and the brand-new MD1CS064 join the tool: VAG's premium diesel segment is covered.

MagicMotorsport · July 1, 2026
More MDG1 TC2xx No RFT: New Models Available
Flex 8.1.0.0 adds new MDG1 units to Boot Glitch mode: FCA MD1CS069 (Ducato), BMW MD1CS001 and Ford MD1CP006.

Autotuner · June 29, 2026
Continental 5WY8
The Continental 5WY8, fitted to a wide range of Ford group vehicles from 2004 to 2015, is now supported.

MagicMotorsport · June 29, 2026
Bosch MDG1 No RFT
Flex 8.0.0.0 introduces unlocking and programming of Bosch MDG1 units (Aurix TC2xx) in the workshop: VAG, BMW, Stellantis, Kia/Hyundai and JLR, no RFT.

Autotuner · June 26, 2026
Bosch MG1CS031 / MG1CS142
MG1CS031 support grows beyond the initial OBD references and the MG1CS142 arrives: VAG's flagship petrol engines move forward.

Autotuner · June 25, 2026
EVPT VCU3000
After Boot mode last February, the EVPT VCU3000 from Stellantis' micro-mobility range gets direct support, simpler in the workshop.

Autotuner · June 24, 2026
Bosch MD1CS004 / MD1CS104
A new step for VAG diesels: Bosch MD1CS004 coverage widens and the MD1CS104 arrives.

Autotuner · June 22, 2026
Bosch MED9.5.10
Back to the icons of the 2000s: the Bosch MED9.5.10 is now supported on the Autotuner tool.

MagicMotorsport · June 22, 2026
GPEC5 No RFT
Flex 7.60.0.0 unlocks the Continental GPEC5 on Jeep and RAM in Boot then programs them via OBD, with the new FLX2.88 cable.

Autotuner · June 19, 2026
Honda MPC5554 / R7F701202 / TC1793
OBD support expands across Honda and Acura with the MPC5554, R7F701202 and TC1793 ECUs, complementing the Keihin update.

Autotuner · June 17, 2026
Honda SHxxxx / TCxxxx
Massive Keihin update: more than two decades of Honda and Acura (SH7058, SH72543, TC1782, TC275) now supported.

Autotuner · June 16, 2026
MyFlasher 2.6.0
MyFlasher 2.6.0 is available on iOS and Android for One users, with a reworked onboarding flow.

Autotuner · June 16, 2026
Subaru SH705x/SH7254x OBD NR BETA
The Subaru range lands in beta: Denso (SH7058, SH7059) and Hitachi ECUs via OBD.

Autotuner · June 15, 2026
Siemens MSS52/MSS54/MSS54HP
The legendary Siemens MSS52, MSS54 and MSS54HP from the BMW M cars are now officially supported.

Autotuner · June 12, 2026
Bosch MG1CS039
The Bosch MG1CS039, the ECU at the summit of Italian engineering, joins the Autotuner protocol list.

Dimsport · June 9, 2026
New OBDII Protocol for Continental SID212 Installed on Ford Vehicles
Race opens an OBDII protocol for Ford's Continental SID212 units: read and write through the diagnostic port.

MagicMotorsport · June 8, 2026
Flex for SID212 SID212EVO No Unlock
Flex 7.59.0.0: direct access to maps and EEPROM on Ford Continental SID212 and SID212EVO, no prior unlock needed.

MagicMotorsport · May 25, 2026
New Flex protocols for Triumph ECUs
Flex 7.58.0.0 brings OBD to the Keihin KTKS_v1 (RH850) and KHR4 (SH72531) on Euro 4 and Euro 5 Triumph motorcycles.

Dimsport · May 12, 2026
RACE supports the new Bosch MSE9.0 installed on CFMOTO models
The new Bosch MSE9.0 fitted to CFMOTO bikes is now supported by Race: motorcycle coverage keeps growing.

MagicMotorsport · May 11, 2026
Exclusive Heavy-duty Flex Solutions
Flex 7.57.0.0 targets commercial and industrial vehicles: Bench and Boot on Delphi ETC3 KWP units for Iveco, Hyundai and Kia.

Dimsport · May 7, 2026
A new exclusive application for the OHW and tractor world.
An exclusive application for the agricultural and off-highway world: the LIDEC ECU2 HD joins Race.

MagicMotorsport · April 28, 2026
Flex for KTKZ2 and KTKZ3
Flex 7.56.0.0 programs Keihin KTKZ2 and KTKZ3 (RH850) via OBD on recent Euro 5+ KTMs, including 2025 and 2026 models.

Dimsport · April 14, 2026
ProTune now supports BOSCH EDC17C76 on BMW Diesel engines
ProTune now supports the Bosch EDC17C76 found on BMW diesel engines.

MagicMotorsport · April 13, 2026
Flex OBD and Boot for Ducati Continental M3D
Flex 7.55.0.0 covers Ducati bikes with Continental M3D ECUs: OBD with the 4-pin MMS03.003 cable, or Boot for full access.

Dimsport · April 8, 2026
New ProTune Update: BOSCH EDC17C79
The Bosch EDC17C79, one of the most widespread diesel ECUs, enters the ProTune catalogue.

MagicMotorsport · March 31, 2026
Flex RFT Service for VAG Bosch MD1CS004 - Ready For Tuning
Flex 7.54.0.0 launches the RFT service for Bosch MD1CS004 (HW 05L907309AA): OBD programming on VAG 2.0 TDI models from 2022 to 2024.

MagicMotorsport · March 30, 2026
Flex OBD Protocol for Ford Fomoco UTCU4 - F-250 and F-350
Flex 7.53.0.0 opens OBD on the UTCU4 transmission units of Ford F-250 and F-350 with 6.7L and 7.3L engines, through the diagnostic port.

MagicMotorsport · March 26, 2026
Flex Bench Support for VAG Bosch DQ500 Gen2, DQ38x, and ZF AL552
Flex 7.52.0.0 brings Bench mode to recent VAG TCUs: DQ500 Gen2, DQ38x (2022+) and ZF AL552 Gen2, cloning included.

MagicMotorsport · March 17, 2026
Flex Exclusive: FCA Marelli 12GF in OBD Mode
Flex 7.51.0.0 exclusive: OBD programming of Marelli 12GF units on modern FCA vehicles, with the SGW Bypass cable MMS03.001.

Dimsport · March 16, 2026
New update for Iveco: BOSCH MD1CS069
The FLASH_0823 protocol evolves: Race now manages the Bosch MD1CS069 fitted to Iveco vehicles.

MagicMotorsport · March 12, 2026
Flex Bench and OBD for Ford Continental SID212 and SID212EVO
With Flex 7.50.0.0, no more RFT on Ford SID212 and SID212EVO: direct read and write on the bench, then OBD after unlock.

Dimsport · March 12, 2026
Dimsport Unlocks MOTION DE08/FE08 ECUs on Zontes
Dimsport unlocks the MOTION DE08 and FE08 ECUs of the new Zontes 703 platforms through the FLASH_0993 protocol.

Dimsport · February 10, 2026
New serial protocol - latest-generation BOSCH MD1xxx
A new serial protocol covers latest-generation Bosch MD1xxx units.

Dimsport · January 22, 2026
Ducati DESMO450 MX: RACE IS ON!
The Ducati DESMO450 MX enters the Race list: Italian off-road joins the lineup.

Dimsport · December 5, 2025
MORE POWER WITH A CLICK ON FORD RANGER: BOSCH MD1CP061
More power in one click on the Ford Ranger: the Bosch MD1CP061 is covered, with ProTune to back it up.

Dimsport · November 27, 2025
PORSCHE ME7.8.x: NOW YOU CAN REMAP THEM WITH PROTUNE
Porsche models running the ME7.8.x ECU can now be remapped with ProTune.

Dimsport · November 20, 2025
NEW PROTUNE FOR THE AGRI WORLD: BOSCH EDC16C39
New ProTune for the agri world: the Bosch EDC16C39 is now supported.

Dimsport · November 6, 2025
DELCO E98 REPROGRAMMING WITH PROTUNE
The Delco E98 can now be reprogrammed with ProTune: Dimsport's calibration service widens its coverage again.

Dimsport · November 3, 2025
NEW SERIAL PROTOCOL FOR BOSCH MG1CS036
New serial protocol for the Bosch MG1CS036: read and write on numerous Ford petrol engines.

Dimsport · October 30, 2025
OBDII REMAPPING FOR FORD RANGER AND VW AMAROK
With the new FLASH_0970 serial protocol, direct OBDII tuning lands on the Bosch MD1CP061 of the Ford Ranger and VW Amarok.
Ready to send your file?
Create your professional account, buy tokens and upload your original read. Your custom file comes back in 60 minutes maximum during opening hours, with a live estimate.
Live estimate · 60 min max during opening hours